| Author |
Topic |
|
|
hongqi
10 Posts |
 Posted - 24 Feb 2004 : 19:18:09
|
We just upgraded our system from BitsyPlus to BitsyX. I have two questions:
1)I tried to display BitsyX's files(like ADS.HWT, ADS.REG) under its debug mode but could not find the feature(6]Display Files in the Flash) from the debug window. I used this feature with BitsyPlus. So what is the way to do it with BitsyX?
2)I tried download recommended CE image file(CE 4.10.35 or .36), but there are not recommended Config files on the same screen. So where could I find latest config files to be downloaded?
Thanks a lot,
|
|
|
akidder
1519 Posts |
Posted - 25 Feb 2004 : 10:04:27
|
Thanks for your message. Here are some answers:
1. The CE launcher for the BitsyX and our other latest CE releases now copies the ADSLOAD.REG and .HWT files to the \Temp folder of the CE file system. There is no longer a need to go to the debug menu for these files. If you are using an older build of CE that doesn't have this feature, you can use the ADSLoadExtract.exe application to put a copy of those files in the \Temp folder.
2. If there's no recommended configuration listed for a particular build, it just means that we may not have explicitly tested that build with a particular set of configuration files. Just look back at previous releases for that product (usually ones of the same size).
In this case you'll see that 16 MiB build 4.10.33, released a couple weeks before 4.10.36, uses configuration file 700115-0700C. That same configuration will work with 16 MiB build 4.10.36. |
 |
|
|
hongqi
10 Posts |
Posted - 25 Feb 2004 : 20:34:46
|
Thanks for the reply. Now I am able to check the config files in Windows\temp folder, but when I upgrade the CE image(CE 4.10.36) and recommended config files to the BitsyX device I still get the trouble.
The massage I've got from the debug mode window during downloading is:
---------------------------------------------------------------------
Reset Detected
******* BitsyX Initialization*******
CPU ID = A0 PXA255
SDCLK[1] = MemClk
MemClk = 99.53 MHz
Run Mode = 4 * MemClk
Turbo Mode = Run Mode
Mode: RUN
Reading Flash ...(from 0x40004 to 0x409ab)
Reading Hardware Ta
Microsoft Windows CE Ethernet Boot Loader
Copyright (c) 2001 Microsoft Corporation
Copyright (c) 2001 Intel Corporation
Copyright (c) 2002~2003 ADS BitsyX Bootloader Ver (1.07 )
(Built at 18:22:15 on Jul 24 2003)
Detected Ethernet(SMC91C111)
CPLD Version = 0x7
DipSwitch = 0x3
BootSwitch = 0x8
ADSLOAD.ROM : Reading ... Writing...
Failed to load ADSLOAD.ROM from an ATA Flash Card.
ADSLOAD.HWT : Reading ... Writing...
Programming flash (this will also take a few seconds).
File Size = 2471(0x9A7) bytes .
Erasing flash...
Successfully Erased !!!!
Writing Flash Header Size...(0x9a7 bytes) .
Writing Flash...(from 0x40004 to 0x409ab).
Compare Memory with Flash, Successfully Done !!!
ADSLOAD.REG : Reading ... Writing...
Programming flash (this will also take a few seconds).
File Size = 4150(0x1036) bytes .
Erasing flash...
Successfully Erased !!!!
Writing Flash Header Size...(0x1036 bytes) .
Writing Flash...(from 0x80004 to 0x8103a).
Compare Memory with Flash, Successfully Done !!!
ADSLOAD.EXE : Reading ... Writing...
Failed to load ADSLOAD.EXE from an ATA Flash Card.
ADSLOAD.BMP : Reading ... Writing...
Failed to load ADSLOAD.BMP from an ATA Flash Card.
NK.BIN : Reading ... Writing...
Programming flash (this will also take a few minutes).
File Size = 16438888(0xFAD668) bytes .
Erasing flash...
Successfully Erased !!!!
Writing Flash Header Size...(0xfad668 bytes) .
Writing Flash Header Size...(0x800b8000 bytes) .
Writing Flash...(from 0x200008 to 0x011ad670).
Compare Memory with Flash, Successfully Done !!!
RegBackup : Erasing...
Reading Flash ...(from 0x40004 to 0x409ab)
Reading Hardware Table(ADSLOAD.HWT) from Flash.
Booting from Flash.
Reading Flash ...(from 0x200008 to 0x011ad670)
CE starts From DRAM(0x800b8000)
Load HWT (Kernel)
Windows CE Kernel for ARM (Thumb Enabled) Built on Feb 12 2003 at 15:36:08
ProcessorType=02d0 Revision=6
sp_abt=ffff5000 sp_irq=ffff2800 sp_undef=ffffc800
Registry area is blank.
Sp=ffffc7d0
FlashFX Disk Detected: Ver 5.10 (Build 492)
-------------------------------------------------------------------
The problem is the system stopped at this point forever with no more running. So I could not go through to get the massage like
"Microsoft Windows CE Ver. 4.10 (build XXXX)
BitsyX Windows CE Ver.(4.10.36)"
What is wrong?
|
|
|
|
steveh
2 Posts |
Posted - 26 Feb 2004 : 09:08:33
|
| I had the same problem. Cured it by upgrading adsload.rom to the latest version (1.10), but I can't say why it made the difference! |
|
|
|
hongqi
10 Posts |
Posted - 26 Feb 2004 : 11:34:49
|
Thanks stave, I upgraded adsload.rom with the latest version (1.10) to my system, but nothing is changed. The same problem is still there. I don't know what can I do now, should I try CE.NET 4.20?
I really appreciate if I could get the help either from ADS or from somebody else!
My phone number here is 425-291-0044
Thanks,
|
|
|
|
hongqi
10 Posts |
Posted - 26 Feb 2004 : 13:23:14
|
Sorry for the interruption. I tried to upgrade again and this time when I removed CF card and reboot the system after a couple of minutes, I was surprised to get system worked even I didn't find the CE version number to be shown on the debug window druing the downloading.
Thanks a lot, |
|
|
| |
Topic |
|
All Forums
Microsoft Windows CE
How to display files under debug mode with BitsyX
Forum Locked
Printer Friendly