All Forums
 Embedded Linux
 Linux Downloads and Documents
 Debian JFFS2 2006-08-29 (Etch)
 Forum Locked
 Send Topic to a Friend
 Printer Friendly
Author Topic  

jhess

135 Posts

Posted - 31 Aug 2006 :  15:33:57  Show Profile  Email Poster

Debian JFFS2 2006-08-29 (Etch)

Debian JFFS2 2006-08-29 is a root file system that is derived from the Debian (Etch) distribution and is trimmed down to fit (compressed) in a partition in on-board flash as small as 15MB. This size can be reduced further by removing the demo programs and associated data that are included in this distribution. See the main README.txt for the 2006-08-29 ADS Debian release for detailed information about the root filesystems.

The ADS Debian JFFS2 root uses x11 (XFree86) as its GUI and includes several demo programs that run under x11. The media files for several of these demos are stored in the /root/demo_media directory. Many common x11 shared libraries are included in the JFFS2 root, including those necessary to run gtk programs.

The JFFS2 filesystem is a persistent flash filesystem that keeps changes across reboots - it is not always the same on each boot (like the ramdisk). Although it is designed to be resilient in the case of power loss and unclean shutdown/dismount, you should shut down your JFFS2 system properly (using the 'shutdown' command) to cleanly unmount the root filesystem.

The following files are included in this release:
bitsyXb/hw_config.txt
bitsyXb/tty_config.txt
bitsyXb/root_config.txt
bitsyXb/start.txt
sphere/hw_config.txt
sphere/tty_config.txt
sphere/root_config.txt
sphere/start.txt
vix/hw_config.txt
vix/tty_config.txt
vix/root_config.txt
vix/start.txt
cmdline_bitsyx.txt
MD5SUMS
register.txt
register_vgx.txt
register_agxepson.txt
flashfs1
cmdline.txt
README.txt
portal/tty_config.txt
portal/root_config.txt
portal/start.txt
portal/hw_config.txt
snapshot.txt
flashfs1-128k
debian-jffs2.tar.gz
700050-4103j.partno


Usage
Download the flashfs1 image and copy it to an ATA flash card. If your board uses 128k flash, download the flashfs1-128k image instead, and copy it to the card with the name "flashfs1".

Also copy onto the card the kernel zImage file for the kernel you want to use.

For systems such as the BitsyXb, Sphere, VIX, and Portal, which use the u-boot bootloader, a set of u-boot configuration files is needed. See this topic for all the available files, download the appropriate files and copy them to the card. Note that you will need at a minimum start.txt, jffs2 root_config.txt, and a tty_config.txt file for your system. A hw_config.txt file for your system's frame buffer is recommended for best performace of the video demonstration programs included in this distribution.

For PXA systems such as the BitsyX, AGX, GCX, VGX, which do not use the u-boot bootloader, a kernel command line is required to direct the kernel to mount this file system during start up. Download a cmdline.txt file as shown below and copy it to the card, then create a file named ProgramFlash.ads! on the card. A register.txt file is recommended for best performace of the video demonstration programs included in this distribution. Download the register.txt file for your system's frame buffer as shown below and copy it to the card.

On your ADS System, set the first dip switch to ON (Flash Update Mode), insert the card, and boot your system. The bootloader will erase everything in on-board flash (except the bootloader itself) and program (copy) the images on the ATA card to on-board flash. The kernel will be loaded from on-board flash and the JFFS2 root file system will be mounted when Linux starts.

Remove the ATA flash card to prevent an unnecessary erase/reprogramming of on-board flash the next time you reboot. See the bootloader manual for more information on the dip switch settings and boot options.


Command lines
These command lines will eliminate the ramdisk partition and direct the kernel to mount the JFFS2 root file system in the third partition. See the bootloader manual for more examples.

On the BitsyX, use this cmdline.txt.

On AGX, GCX, and VGX, use this cmdline.txt.


Register Settings
These register.txt files will change the default 8bpp color depth to 16bpp. The bootloader reads the register.txt file and changes the registers before the kernel starts. Download the one for the frame buffer that is used by your board.

register.txt for PXA frame buffer and LQ64343 LCD (BitsyX, GCX, or AGX without an Epson chip)

register.txt for Epson frame buffer and LQ64343 LCD (AGX with an Epson chip)

register.txt for SM501 frame buffer and LCD or CRT (VGX)


Tar Archive
Here is a tar archive of the contents of the jffs2 image.


Verification
MD5SUMS provides MD5 checksums for all files in this release.


History
This release of our JFFS2 root file system supersedes our previous 2006-05-26 release. It is derived from the full Debian root filesystem and is similar to our Debian Ramdisk root file system but with X11 instead of Microwindows / nano-x and with more features, demos, etc.

  Topic  
 Forum Locked
 Send Topic to a Friend
 Printer Friendly
Jump To:
Eurotech Support Forums © Eurotech Inc. Go To Top Of Page
This page was generated in 0.03 seconds. Snitz Forums 2000