| Author |
Topic |
|
|
dorgant
46 Posts |
 Posted - 17 Dec 2003 : 00:01:34
|
Hello,
I have a new AGX Development system with a 10.4" Sharp LQ104S1DG21 Display and a MicroTouch RES-10.4-PL4 touch screen.
Booting up in normal mode, the display looks fine. However, the touchscreen does not work properly. The most I can make it do is flicker a bit if I run my finger down the row of icons on the left side of the screen.
I wanted to upload the .reg and .hwt to use in getting help on this issue. However, given the displayed menu (shown below), I don't know how to do that. It's not the same menu I see in the Getting Started Guide or on my old GC system. I'm looking for the "6] Display Files in the Flash" option.
Ethernet Boot Loader Configuration:
0) Display Register
1) Set Register
2) Dump Memory
3) Boot delay: 0 seconds
4) DHCP: Disabled
5) Erase Flash Memory
6) ST16C554 UART Test
7) Program RAM image into FLASH (Disabled)
8) Program SMSC MAC address
9) Boot device order: PCMCIA -> CF -> SMSC
A) Download image from ATA card
B) Copy CE Files from ATA card to Flash Memory
C) Launch Existing Flash resident Image now
D) Download image now (Ethernet)
E) Test Memory (DRAM)
f) IP address: 0000
g) Subnet mask: 0000
h) # bootme's: 0
Enter your selection: |
|
|
ctacke
877 Posts |
Posted - 17 Dec 2003 : 09:32:17
|
| The AGX boot menu is indeed different. To extract your REG and HWT files, first check in the Control Panel to see if you have the 'Configuration' applet, which is in the newer AGX builds and allows file import, export and viewing. If it's not there you can use ADSLOADExtract.exe to dump the files into the device's \Temp directory. |
 |
|
|
akidder
1519 Posts |
Posted - 17 Dec 2003 : 10:21:04
|
It's also easy to intiate recalibration using a keyboard. Take a look at the notes I posted at topic 1287 for details.
I guess you're converting your Graphics Master development system over to the AGX? Let us know how we can help! |
|
|
|
dorgant
46 Posts |
Posted - 17 Dec 2003 : 23:29:47
|
Ok, Thanks. I guess I will need to connect a keyboard and/or mouse since the touchscreen is out of commission. Can I connect both at once? Does the system only drive a USB keyboard or can I find a cable for use with the J9 socket? I looked around in the AGX User's Manual and the various topics on this site and did not find the information. I was using the 2 PS/2 ports on the Graphics Master for keyboard and mouse and they always worked well.
thanks,
Tom. |
|
|
|
akidder
1519 Posts |
Posted - 18 Dec 2003 : 12:58:51
|
Hi Tom. You can use USB and PS/2 keyboards at the same time. A USB mouse will work, too.
I recommend hooking up a USB keyboard, since the connector is already on the AGX. You can use the keyboard from your PC since it only takes a minute to recalibrate the AGX touch panel as described in topic 1287. |
|
|
|
ctacke
877 Posts |
Posted - 18 Dec 2003 : 13:07:36
|
I just tried a keyboard that has an on-board USB hub with a USB mouse plugged into that (so a mouse plugged into a keyboard, which is in turned plugged into an AGX) and it worked fine on build 4.10.12.
|
|
|
|
dorgant
46 Posts |
Posted - 20 Dec 2003 : 11:05:29
|
I plugged in a Microsoft USB Wheel mouse into J1. I powered the machine. It was in Debug Mode (dip switch one set off). I powered down and reset SW1. I powered up and got a trashed display. I unplugged the mouse and tried again. I am getting an error message:
Data Abort: Thread=83f62000 Proc=8104f2bc 'device.exe'
AKY=00000009 PC=028c1c10 RA=00013204 BVA=f8100000 FSR=00000005
CADSFileOnBoardFlash::GetNextLine::SetFilePointer failed
REG_Init::ParseF.ParseFile() failed
I checked and reseated the video, touchscreen and flash cards. I am seeing D9 green and D7 Red.
Here is the entire boot output:
Reading Flash ...(from 0x40004 to 0x41198)
Reading Hardware Table(ADSLOAD.HWT) from Flash.
Copyright (c) 2001 Microsoft Corporation
Copyright (c) 2001 Intel Corporation
Copyright (c) 2002,2003 Applied Data Systems Inc.
AGX Bootloader (Ver 1.02 )
(Built at 09:13:46 on Jul 18 2003)
CPLD Version = 0x7
Board Revision = 0x0
DipSwitch(S1) = 0x5
BootOption :
Read CE Image from Flash and Start Windows CE
Booting from Flash.
Reading Flash ...(from 0x200008 to 0xf25184)
CE starts From DRAM(0x800B8000)
Windows CE Kernel for ARM (Thumb Enabled) Built on Feb 12 2003 at 15:36:08
ProcessorType=02d0 Revision=6
sp_abt=ffff5000 sp_irq=ffff2800 sp_undef=ffffc800
Registry area is blank.
Sp=ffffc7d0
Data Abort: Thread=83f62000 Proc=8104f2bc 'device.exe'
AKY=00000009 PC=028c1c10 RA=00013204 BVA=f8100000 FSR=00000005
CADSFileOnBoardFlash::GetNextLine::SetFilePointer failed
REG_Init::ParseF.ParseFile() failed
FlashFX Disk Detected: Ver 5.10 (Build 492)
Ethernet Detected : SMC91C111.
Scanning Installed Providers
Installing Layered Providers
Installed over Windows C
E MS Tcpip [UDP/IP].
Installed over Windows CE MS Tcpip [UDP/IP].
Installed over W
indows CE MS Tcpip [TCP/IP].
Installed over Windows CE MS Tcpip [TCP/IP].
Can't Re
order under CEPreparing To Reoder Installed Chains
CAN SJA1000:initialized
SMARTIO Detected : PartType=0x8535 Firmware=0x4004 Revision=4
Microsoft Windows CE Ver. 4.10 (build 908)
AGX Windows CE Ver.(4.10.04)
* ADSLOAD.EXE(do-nothing build): Complete
|
|
|
|
akidder
1519 Posts |
Posted - 22 Dec 2003 : 11:55:52
|
Hi Tom:
It looks like your registry file has gotten corrupted ("REG_Init::ParseF.ParseFile() failed"). You might take a look at them to see what got messed up, or you can zip the files you're using and send them to us to check out.
You might also consider pulling down the latest AGX build and configuration files. We released build 4.10.12 last week.
edited 24-June-2008 by ljoy: Replaced obsolete link
|
|
|
| |
Topic |
|
All Forums
Microsoft Windows CE
AGX Debug Menu (touch panel recalibration)
Forum Locked
Printer Friendly